Sensor input（Standard）｜Sensor input（Multisensor input：MLT）｜Analog voltage output｜Display section｜COMP. & JUDGE. function｜Preventive maintenance support｜External signal｜Interface｜General performance｜Attachments
| Sensor input | |
| Sensor input for load (Fixed as strain gauge input)(6-wire) | |
| Excitation voltage |
DC 2.5, 5, 10V±10% (depending on settings) Output current: Within 30mA |
|---|---|
| Signal input range | -2.0mV/V to +2.0mV/V |
| Accuracy |
Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input) Zero drift: Within 0.1μV/℃ RTI Gain drift: Within 15ppm/℃ |
| Low-pass filter |
Selectable from 10 to 10kHz（at A/D converter speed 25000 times/sec） Selectable from 2 to 2kHz（at A/D converter speed 5000 times/sec） |
| A/D converter |
Speed: Selectable from 25000 times/sec., 5000 times/sec. Resolution: 24bit (binary) |
|
Sensor input for displacement Pulse input(Line driver) |
|
| Max. input frequency | 1MHz |
| Internal count range | Approx. 1,000,000 |
| Adaptable rotary encoder |
Output: Incremental type 2-phase output (A/B signal output) Also capable of single-phase output (A-phase input used. All pulses are counted as in the plus direction.) Output stage circuit specification: Line driver (Based on RS-422) |
| Sensor input（Multisensor input：MLT or MLT2） | |
| Sensor input for load (Fixed as strain gauge input)(6-wire) | |
| Excitation voltage |
DC 2.5, 5, 10V±10% (depending on settings) Output current: Within 30mA |
|---|---|
| Signal input range | -2.0mV/V to +2.0mV/V |
| Accuracy |
Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input) Zero drift: Within 0.1μV/℃ RTI Gain drift: Within 15ppm/℃ |
| Low-pass filter |
Selectable from 10 to 10kHz（at A/D converter speed 25000 times/sec） Selectable from 2 to 2kHz（at A/D converter speed 5000 times/sec） |
| A/D converter |
Speed: Selectable from 25000 times/sec., 5000 times/sec. Resolution: 24bit (binary) |
|
Sensor input for displacement Pulse input (Open collector)[MLT] |
|
| Max. input frequency | 1MHz |
| Internal count range | Approx. 1,000,000 |
| Adaptable rotary encoder |
Output: Incremental type 2-phase output (A/B signal output) Also capable of single-phase output (A-phase input used. All pulses are counted as in the plus direction.) Output stage circuit specification: Open collector (built in pull-up resistor) |
|
Sensor input for displacement Pulse input(Line driver)[MLT2] |
|
| Max. input frequency | 1MHz |
| Internal count range | Approx. 1,000,000 |
| Adaptable rotary encoder |
Output: Incremental type 2-phase output (A/B signal output) Also capable of single-phase output (A-phase input used. All pulses are counted as in the plus direction.) Output stage circuit specification: Line driver (Based on RS-422) |
| Voltage input | |
| Signal input range | －10 to ＋10V |
| Input impedance | App. 1MΩ |
| Accuracy |
Non-linearity:Within 0.02%/FS ±1 digit (at 10V input) Zero drift:Within 0.2mV/℃ RTI Gain drift:Within 0.01%/℃ |
| Low-pass filter |
Selectable from 10 to 10kHz（at A/D converter speed 25000 times/sec） Selectable from 2 to 2kHz（at A/D converter speed 5000 times/sec） |
| A/D converter |
Speed:Selectable from 25000 times/sec, 5000 times/sec Resolution:24bit Effective Resolution: Approx. 1/20000 against 10V |
| Analog voltage output |
Output level: Approx. 2V per 1.0mV/V input Load resistance: 2kΩ or more |
|---|
| Display section | |
| Display |
4.3 inch TFT color LCD module Display area: 95.0(W)×53.9(H) mm Dot configuration: 480×272 dot |
|---|---|
| Display frequency | Fixed at 3 times/sec. |
| COMP. & JUDGE. function | |
|
Multi point comparison mode 16ch (setting values can be stored) |
Capable of judging up to 5 hold points at the same time. Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End |
|---|---|
|
Waveform comparison mode 16ch (setting values can be stored) |
Compares the actually measured waveform against the preset Hi/Lo waveforms. The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK. |
| Preventive maintenance support | |
| Trend display | Showing the trend of measurement data to help finding irregularities at early stage. |
|---|---|
| Statistics |
Using the latest 10000 measured data. Displaying number of measurement, OK, NOK |
| Screen capture | Saves screen capture data as bmp data. |
| Work name edit | Work name can be edited and displayed for each Work No.. |
| Setting list display | Changed setting items comparing to master set values are highlighted. |
| User management | Login ID and Password |
| External signal | |
| Output signal |
16 points Hold judgment (load, displacement)/ Load overload/ Measurement complete/ Waveform comparison judgment/ Load & displacement OK/ CPU OK/ SD card OK/ Timing output 1,2 Output Type: Sink type/source type selectable. (Source Type is option: [ISC]) Output transistor ON at signal ON. To connect an input unit like a PLC, connect plus common for sink type, and minus common for source type. Rated voltage: 30V Rated current: 30mA |
|---|---|
| Input signal |
16 points Load digital zero/ Displacement adjustment/ Measurement start/ Measurement end/ HOLD1 to 5/ Reset/ Forcibly light up the backlight/ Touch panel lock/ Work change Input type: Plus common/Minus common selectable. (Minus common is option: [ISC]) To connect a transistor, connect NPN output type (sink type) for plus common and PNP output type (source type) for minus common. |
|
Interface Only one option can be installed. |
|
| USB | USB interface |
|---|---|
| ODN | DeviceNet interface (option) |
| CCL | CC-Link interface (option) |
| EIP | EtherNet/IP interface (option) |
| General performance | |
| Power supply voltage | DC24V (±15%) |
|---|---|
| Power consumption | 6W typ |
| Operation condition |
Operation temperature: -10℃ to +40℃/ Storage temperature: -20℃ to +60℃ Humidity: 85% RH or less (non-condensing) |
| Dimensions | 132(W)×98(H)×110(D) mm (Projections excluded) |
| Weight | Approx. 1.0kg |
| Attachments | |
| I/O connector (with cover) | 1 |
|---|---|
| Analog connector | 1 |
| Operating tool | 1 |
| SD card | 1 |
| Operation manual | 1 |
| DeviceNet connector (when DeviceNet option is selected) | 1 |
| CC-Link connector (when CC-Link option is selected) | 1 |
| Model | |
| ISC | I/O source board |
|---|---|
| MLT | Multisensor input |
| MLT2 | Multisensor input |
| ODN | DeviceNet interface |
| CCL | CC-Link interface |
| EIP | EtherNet/IP interface |
| Model | |
| CN71 | CC-Link connector |
|---|---|
| CN72 | Double row connector for CC-Link |
| CN77 | Analog connector |
| CND01 | DeviceNet connector |
| SD1G | 1 GByte SD card |
| SD2G | 2 GByte SD card |
| SD16G | 16 GByte SD card |
| SD32G | 32 GByte SD card |
| CA81-USB | USB cable (A-miniB type) 1.8m |
| TSU03 | DC lighting surge unit |
iMS Motion Solution (Johor) Sdn Bhd (Company Registration 1098771-W)
whatsapp us now !
Return / Refund Policy :
All goods sold are not returnable & we accept goods ex-change with equal or lower value of good purchased. If the ex-change items are higher than purchased items, buyer shall top up the differential cost. All payment made are not refundable, please confirm the purchase items code & cost with our sales representative before place orders.
Shipping and Fulfillment :
Thank you for your purchase. Once we have confirmed your payment, we will prepare and ship out your order out within 24-48 hours.( For ex-stock items only, Indent items subject to delivery stated in quotation & conversation in emails). Once your order has been shipped out, you will receive an email notification with the tracking number and tracking details inside.
Private Policy
General Statement of Principles
As described in detail below, any information we gather at this web site is strictly for our use and is not shared with any other entity, public or private, for any reason - period. We will not sell or give away any lists or other data that we may retain and we do not purchase such information from other sources.
Statistical Data
Our servers (as most) track IP addresses and referring pages to help with site maintenance and improvements. This data is viewed only as anonymous statistics to show the busiest times of the day or week, pages with errors and how effective our advertising has been. This information is not used for any other purpose.
Personal Information Collected - Order Forms
With the exception of credit card info, we store the information from your order form to allow us to track consulting issues or refer to a previous order to help provide some customer service. You may elect to have your information completely removed from this system by e-mailing us at [email protected] with your request. We do not store any type of sales information.
Information Correction or Removal
If you wish to correct, update or remove any information about you that may be in our records, please send us e-mail at [email protected] with the details of your request. If you wish to contact us further, please find complete contact information on our contact page.
Cookies
Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a web site and stored on your computer's hard drive. We use 'cookies' to store your cart contents for you. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use the checkout section of our site.
Changes To This Privacy Policy
This Privacy Policy is effective as of 1st Jan 2019 and will remain in effect except with respect to any changes in its provisions in the future, which will be in effect immediately after being posted on this page.
Malaysia
